- #Boson netsim 11 commands not working serial#
- #Boson netsim 11 commands not working manual#
- #Boson netsim 11 commands not working full#
- #Boson netsim 11 commands not working simulator#
- #Boson netsim 11 commands not working download#
Upload this document through Moodle with the screen shots included. After finishing the second demo lab, optionally you could then do the Using NetSim and the Topology Demo labs, but this is not required for this assignment and there is nothing to turn in for these other two labs. What command(s) did you enter to verify your configuration? _ġ2. What commands did you enter to configure EIGRP to announce all networks that are directly connected to the routers specifying each subnet? _ See how many of the commands you remember when just given the task and not the commands. When you finish, go back to the Lab Tasks section above and look at what you are asked to do in each task. Task 4, #1, the three pings from PC1 to PC2 and PC3 and PC4ġ1. Task 3, #2, the screens showing the configuration of EIGRP on the four routers As you are doing this lab, screen print the console window where you are entering the commands for the following items, and insert the screen shots in order immediately below. As you did in Demo Lab 1, read through the introduction, objectives, topology, and command summary, then proceed to the Lab Solutions section and enter all the commands listed into the console window.ġ0. Now, in the Standard tab on the left pane, click on Demo to open it up and select Configuration Demo 2:ĩ. What commands did you enter to configure the routing protocol EIGRP? _Ĩ. What commands did you enter to set the IP address on the interface FastEthernet 0/0? _
#Boson netsim 11 commands not working serial#
What commands did you enter to set the IP address on the interface Serial 0/0? _ What commands did you enter to set the hostname of the router? _ See how many of the commands you remember, having just executed them, when you are only given the task without the command. When you finish, go back to the Lab Tasks section above (the section you skipped through quickly) and look at what you are asked to do in each task. As you are doing this lab, screen print the console window where you are entering the commands for the following items, and insert the screen shots in order immediately below.ħ.
When asked in the instructions to use a different device, select it from the list right above the console window:Ħ. In the CS 289 Cisco Router and Switch Administration course (a required course in the networking degree), you will execute these commands on real Cisco routers.ĥ. These are actual Cisco IOS commands that are being simulated with the NetSim software. Enter each of the commands in the Lab Solutions section into the console window below for each of the Tasks shown. Just look through this quickly and proceed to the Lab Solutions section farther down in the document.Ĥ. When you get to the Lab Tasks portion of the document, there are instructions that you are asked to perform given not the actual commands you would enter in the console window below, but what it is that needs to be done. Read through this information carefully.ģ.
In the instructions, first there is a description and illustration of the internetwork you are implementing, and the commands you will use and what the lab’s purpose is. After clicking on Try the Demo Lab, a console screen will appear at the bottom of the window (it says Press Enter to Start). Select the Demo Lab option when you see the link:ġ. When you re-launch NetSim, always select demo mode as shown below:ĩ. When you are asked if you want to activate or demo NetSim, select demo (see below).Ĩ. After downloading it, if NetSim doesn’t automatically launch then launch it yourself.ħ.
#Boson netsim 11 commands not working download#
Select the NetSim Download Installer button, not the Boson Exam Environment (see below).Ħ.
It will ask you to login by creating an account. Use your browser to navigate to Then click the Download Demo button on the home page. If you are doing this assignment from a classroom computer where NetSim is already installed go to Part A at the bottom of this document.Ĥ. You want the free demo labs for this assignment.ģ. They have practice labs on their site as well, but they charge for these.
#Boson netsim 11 commands not working manual#
The Boson website includes the download NetSim option, as well as a user manual and NetSim demo videos which you are invited to look at especially if you have problems doing the demo labs for this assignment. It gives you experience configuring a Cisco router without needing the hardware.Ģ.
#Boson netsim 11 commands not working full#
Boson charges for the full version, but there is a free demo version that will work quite nicely for us.
#Boson netsim 11 commands not working simulator#
Intro: We will use a Cisco router simulator for this assignment: NetSim (Network Simulator) from Boson. You may find it useful to review the Routers Power Point and the Routing Essentials handout in Moodle.ġ. You will create screen shots and insert them in this document then upload it through Moodle.
0 kommentar(er)
